Massachusetts Institute of Technology
Sign in | Create Account

Machine Shop 2

Machining Skills for Prototype Development:

1) Basic 2
2) Drilling Holes
3) Special Drills for Plastics and Hard or Abrasive Materials
4) Drill Press Limitations
5) Bandsaw
6) Suitable Speeds, Feeds and Materials
7) Bandsaw Setup
8) Using the Drill Press Vise

Duration 57:33

Comments (28)

Notes by Shawna 04/15/08 10:09

Machine Shop 2 Machining Skills for Prototype Development:

10:10 1) Basic 2 drill & tap heads

10:11 2) Drilling Holes larger aspect ratio (thicker) use cutting fluid b/c chips have harder time clearing the drill keeps chips cool and lubricates them so they slide out of hole. chatter caused by drill jumping around hole: running drill too fast. may need to change transmission ratio for diff sized bits if there is chatter that speed change will not fix. if levers don't shift, something needs to turn, either motor or spindle. step-up drill size. sensitive chuck for hand feeding very small bits… very cool.

10:30 3) Special Drills for Plastics and Hard or Abrasive Materials softer materials: high helix angle of normal bit will dig down and possibly pull part up out of device when used with some materials ie. plastics lower helix angle will scrape rather than cut allows safe drilling of materials that may tend to be lifted up hard materials: steel, ciruit boards (fiberglass) use tunsgton carbide drill.

10:34 4) Drill Press Limitations chatter when used as milling machine.. irregularities. lack of stiffness cannot handle the load of an arbor press (sp??)

10:38 5) Bandsaw cut down larger peices of stock to near net size of part you want to make narrow blade makes it possible to cut curves. 3 teeth always in contact with part.. otherwise risk damaging blade noise of using a coarse blade can be danger to those in shop… 10:42

10:43 6) Suitable Speeds, Feeds and Materials

10:51 7) Bandsaw Setup proper handling & blade guard guidance… 10:52 posture, stand squarely, hands firm on bed of machine. safe handling & proper hand placement. until 10:54

10:54 8) Using the Drill Press Vise round stock. use vice to avoid getting cut by spinning part

10:56: end.

Posted almost 6 years by Anonymous User

bandsaw guard detail in section 7

Posted almost 6 years by Anonymous User

Never allow any part of your body to contact the blade of any machine while the machine is energized. if you need to contact the blade, disconect the power source. Essentially, this person has just bet his fingers on a ten dollar switch.

Posted over 5 years by Anonymous

Aluminum chips are relatively safe if you are gentle. If you rip out the chips or ribbon it will cut you up.

Posted 4 years by Anonymous 00:15:45

Some of the previous comments were inaccurate… need to pay more attention ;)

Posted 4 years by Anonymous 00:57:21

These videos accompany a course at MIT

Posted 4 years by Anonymous 00:17:04

Will be nice if teacher mentions the type of lubricant used

Posted 4 years by Anonymous 00:17:04

No! No! No! Never remove chips and turnings with your bare hands. Use a chip brush or pliers.

Posted 4 years by Anonymous 00:15:45

Huh? Oh, I get it. You’ve never worked in a machine shop that did production work.

Posted 4 years by Anonymous 00:15:45

Just have to get one stuck in your finger once. Then you don’t do it anymore.

Posted 4 years by Anonymous 00:15:45

for a begginer this series of videos is awesome.

Posted 4 years by Anonymous 00:25:56

Wrong title here

Posted 4 years by Anonymous 00:45:00

No, this is the correct title.

Posted 4 years by Anonymous 00:45:00

some chattering..should use a finer blade for steel…

Posted 4 years by Anonymous 00:38:07

Why it go blank???

Posted 4 years by Anonymous 00:51:46

That applies to non-round stock also .

Posted 4 years by Anonymous 00:46:09

If your still watching this, you may want to consider moving on to the next video. :)

Posted 4 years by Anonymous 00:56:11

There’s still things to learn

Posted 4 years by Anonymous 00:56:11

I am about to fall aslee…zzzz

Posted 4 years by Anonymous 00:16:45

don’t put that!

Posted 4 years by Anonymous 00:16:45

End of video.

Posted 4 years by Anonymous 00:46:28

Check out the quill movement -

Posted over 3 years by Anonymous 00:27:27

You can see the chuck really bouncing along here

Posted over 3 years by Anonymous 00:27:40

hmm. interesting. I’ve never seen one of those before!

Posted almost 2 years by Anonymous 00:19:59

Looks like mineral oil based, water miscable cutting fluid

Posted almost 2 years by Anonymous 00:17:21

Albrecht chuck, German made

Posted almost 2 years by Anonymous 00:20:19

the is really cool

Posted over 1 year by Anonymous 00:00:16

insert here

Posted 3 months by Anonymous 00:00:00

You need to log in, in order to post comments. If you don’t have an account yet, sign up now!

Prototype Machining

Prototype Machining

Updated over 4 years ago

Created
April 07, 2008 13:57
Category
Tags
License
All Rights Reserved (What is this?)
Additional Files


Viewed
100846 times

More from Prototype Machining

Machine Shop 7

Machine Shop 7

Added over 6 years ago | 00:45:32 | 81723 views

Machine Shop 5

Machine Shop 5

Added over 6 years ago | 01:03:00 | 92172 views

Machine Shop 1

Machine Shop 1

Added over 6 years ago | 00:40:32 | 309274 views

Machine Shop 4

Machine Shop 4

Added over 6 years ago | 00:50:32 | 113223 views

Machine Shop 10

Machine Shop 10

Added over 6 years ago | 00:34:31 | 104593 views

Machine Shop 9

Machine Shop 9

Added over 6 years ago | 00:47:02 | 92295 views